Difference between revisions of "Scaling Tendencies"

From wiki.olisystems.com
Jump to: navigation, search
(Calculating Scaling Tendency: An Example)
(Calculating Scaling Tendency: An Example)
Line 91: Line 91:
 
[[Category: Scaling and solid formations]]
 
[[Category: Scaling and solid formations]]
 
[[Category: Former Tips]]
 
[[Category: Former Tips]]
[[user:DMILLER | Authors: Jim Berthold and Diana Miller]]
 

Revision as of 14:43, 13 February 2020

What is Scaling?

Scaling is the deposition of a mineral salt on processing equipment. Scaling is a result of supersaturation of mineral ions in the process fluid. Through changes in temperature, or solvent evaporation or degasification, the concentration of salts may exceed the saturation, leading to a precipitation of solids (usually crystals).

To understand Scaling, the Scaling Tendency and Scaling Index definitions are used. These definitions depended on the Solubility Product Constant, Ksp and Ion Activity Product, IAP definitions.


Solubility Product Constant, Ksp

The solubility of ionic compounds of salts and minerals in water are governed by a solubility equilibrium expression and a solubility product constant known as Ksp. It is important to note that the solubility product, Ksp is a function of both temperature and pressure. Consider the general dissolution reaction below (in aqueous solutions):

aA(s)⇌bB(aq)+dD(aq)

With equilibrium constant Ksp defined as:

Ksp=(aB)b∙(aD)d

Where, aB and aD are the activities of the aqueous species. The activity of any species i is defined as the product of its concentration in molality by its corresponding activity coefficient:

ai=mi γi


Ion Activity Product, IAP

A real solution may not be in the state of equilibrium. This non-equilibrium state is described by the ion activity product (IAP). It has the same form as the equilibrium constant Ksp, but involves the actual activities of the species in solution.

IAP=(aB)bactual∙(aD)dactual

Scaling Tendency and Scaling Index

The Scaling Tendency (ST) is defined as the ratio of the Ion Activity Product (IAP) divided by the equilibrium constant (Ksp).


Equation (1) ST=IAP/Ksp


Scaling tendencies are essentially saturation ratios. Thus, if

  • ST < 1 Indicates sub-saturation, and the solid is not expected to form
  • ST = 1 Indicates saturation, and the solid is in equilibrium with water
  • ST > 1 Indicates supersaturation, and solids will form


Note: The Scaling Tendency (ST) is reported in the software as Post-Scale.


The Scale Index (SI) (aka: Saturation Index in the literature), is given by the following relationship:


Equation (2) SI =log10(IAP/Ksp)


Thus, if

  • SI < 0 Indicates sub-saturation, and the solid is not expected to form
  • SI = 0 Indicates saturation, and the solid is in equilibrium with water
  • SI > 0 Indicates supersaturation, and solids will form


Note: The Scaling Index (SI) is reported in the software as SI, Index

Pre-Scaling Tendency and Scaling Index

Pre-Scaling tendency is defined as the scaling tendency before any solids are formed (this can be seen as all the species suspended in solution). The same formulas for ST and SI are applied (Equations 1 and 2).

The Pre-Scaling tendency is reported in the software as Pre-Scale.


Note: Many industries, notably the up-stream oil & gas industry, use the pre-scaling tendency to make design decisions about adding anti-scaling and anti-fouling agents or if the asset is as risk.

Difference between Post-scale and Pre-scale

  • Pre-Scale: The saturation ratio before solids precipitate.
  • Post-Scale: The saturation ratio AFTER solids precipitate (if solids are selected).
  • S, ST – Saturation, Scale Tendency: The ratio of the concentration (activity) to its solubility (S=1).
  • SI – Scale Index: Log(ST).


Scaling Tendency is the saturation ratio after all potential solids come to equilibrium with water. This is the true equilibrium condition (time=∞). I

Pre-scaling Tendency represents the condition before any solids are allowed to form. This is a non-equilibrium condition and can be viewed as the condition where time=0.

Calculating Scaling Tendency: An Example

Below there is an example of how the software calculates the Scaling Tendency.

Scaling tendency example.png